Jet Plans:

Airwolf (TakeTea)
Designer: Taketea
Designer Email: Taketea Email
Specs: Unknown
Material Required: Paper Stock
Downloads available:
Notes:

Airwolf Helicopter
Designer: honeybee
Designer Email: Honeybee at RCGroups
Specs: 11g AUW
Material Required: Paper or card stock
Downloads available:
Notes: Another neat design from Honeybee! Here are the specs:

Airwolf fully armed ;) Weight 11 gr / 7-8 minutes Flight Time.

Apache Longbow Helicopter
Designer: tobu
Designer Email: Tobu at forum.xufo.net
Specs: Unknown
Material Required: Paper Stock
Downloads available:
Notes: Tobu's latest is an Apache Longbow! While a work in progress, it is very impressive. Here is what he has to say ".... it came out quite nice, but overall weight is high. I added some transparent nose canards and the apache went forwards decently.... Any hints or ideas would be very much appreciated! I will keep you posted anyways, hope ya like it..."

BK117 Helicopter
Designer: honeybee
Designer Email: Honeybee at RCGroups
Specs: N/A
Material Required: Paper or card stock
Downloads available:
Notes: Here are some excellent paper bodies for your PiccoZ from Honeybee!

Bell 206 Jet Ranger
Designer: Taketea
Designer Email: Taketea Email
Specs: Unknown
Material Required: Paper Stock
Downloads available:
Notes: Taketea has a created a Bell 206 Jet Ranger using papercraft. Thanks Taketea!

Bell 222
Designer: dz1sfb
Designer Email: dz1sfb at RCGroups
Specs: 11g AUW
Material Required: Depron
Downloads available:
Notes: I used 2 laminations of 2mm depron for the landing gear with paper images of the landing gear laminated to the out side. Very solid and light.
I have some additional info that may be useful to anyone wanting to know how it was done. Basically a Powerpoint file with 3 view that prints right to size. This file is located in PDF link above.


A nose weight was required to balance (1/8" dia. X 3/16" long tungsten). Flying time slightly reduced, but looks too good in the air to matter.

CH55 Aircrane
Designer: Taketea
Designer Email: Taketea Email
Specs: Unknown
Material Required: Paper Stock
Downloads available:
Notes: Taketea has a created a CH55 Aircrane using papercraft. Thanks Taketea!

HSS-2 SeaKing
Designer: Taketea
Designer Email: Taketea Email
Specs: 11.1g AUW
Material Required: Paper Stock
Downloads available:
Notes: Taketea has come up with his own version of the SeaKing paper body. Thanks Taketea!

Jet Ranger
Designer: Christian Bürger
Designer Email: Author home page
Specs: Jet Ranger Heli
Material Required: 2 or 3mm Selitron (Dupron)
Downloads available:
Notes: A F A S T heli! Here is a translation of what the author says about this design: "After the breakdown of the included 60mAh battery of Torstens PiccoZ (He had a pin in the bow of the helicopter which hit the battery when he flew into a wall ;) ) he wanted to use an 150mAh battery of an XTwin instead. Since the old hull was damaged due to the smoking battery a new hull must be built. That's why he now has this beautiful Jet Ranger.

Due to the higher weight of the battery the CG moved to the front, that's why the PiccoZ is much faster now. Unfortunally the flying time is not much longer than with the small battery, as the helicopter will only fly with a full battery. "

MH53E Seadragon
Designer: Taketea
Designer Email: Taketea Email
Specs: Unknown
Material Required: Paper Stock
Downloads available:
Notes: Taketea has a created a Seadragon using papercraft. Thanks Taketea!

RAH-66 Comanche
Designer: JPOP
Designer Email: JPOP at RCGroups
Specs: 9.8g AUW
Material Required: 2 or 3mm Selitron (Dupron)
Downloads available:
Notes: I want to build an nice RAH-66 Comanche Body for my Silverlit PiccoZ. The body is composed of 3 layers of Depron. The inner layer takes the mechanical parts, the two outer layers close the thing. It will start and land on the "open weapons bay", the original EPP landing gear. Its not too slow, the CG is quite a bit forward.

Sea King
Designer: IPal
Designer Email: IPal at RCGroups
Specs: 11g AUW
Material Required: Blue Floormate 200 foam
Downloads available:
Notes: Here's my spin on the Picco. Carved from blue Floormate 200 foam. Weight 11 gms - only other mods are ballraces and carbon shaft. Flies a treat. Paint is Tamiya acrylic with computer generated decals using SuperCal. The sharp eyed may spot that the stabiliser is on the wrong side - but so is the tail rotor! Haven't yet figured out how to get the winch to work.

UH60J SeaHawk
Designer: Taketea
Designer Email: Taketea Email
Specs: Unknown
Material Required: Paper Stock
Downloads available:
Notes: Taketea has a created a UH60J SeaHawk using papercraft. Thanks Taketea!

Z-Bee
Designer: Neurotex
Designer Email: Neurotex at RC Universe
Specs: Unknown
Material Required: 1/16 inch balsa
Downloads available:
Notes: Neurotex created these plans & pics for the Havoc. He said that It might have been easier to build up with foam instead of
balsa but it is quite sturdy. He originally had installed a canard on the front but that made it too quick to control in his living room.